GRASS logo

Note: A new GRASS GIS stable version has been released: GRASS GIS 7.6, available here.
Updated manual page: here

NAME

r.fillnulls - Fills no-data areas in raster maps using spline interpolation.

KEYWORDS

raster, elevation, interpolation

SYNOPSIS

r.fillnulls
r.fillnulls --help
r.fillnulls input=name output=name method=string [tension=float] [smooth=float] [edge=integer] [npmin=integer] [segmax=integer] [lambda=float] [--overwrite] [--help] [--verbose] [--quiet] [--ui]

Flags:

--overwrite
Allow output files to overwrite existing files
--help
Print usage summary
--verbose
Verbose module output
--quiet
Quiet module output
--ui
Force launching GUI dialog

Parameters:

input=name [required]
Name of input raster map
output=name [required]
Name for output raster map
method=string [required]
Interpolation method to use
Options: bilinear, bicubic, rst
Default: rst
tension=float
Spline tension parameter
Default: 40.
smooth=float
Spline smoothing parameter
Default: 0.1
edge=integer
Width of hole edge used for interpolation (in cells)
Options: 2-100
Default: 3
npmin=integer
Minimum number of points for approximation in a segment (>segmax)
Options: 2-10000
Default: 600
segmax=integer
Maximum number of points in a segment
Options: 2-10000
Default: 300
lambda=float
Tykhonov regularization parameter (affects smoothing)
Used in bilinear and bicubic spline interpolation
Default: 0.01

Table of contents

DESCRIPTION

r.fillnulls fills NULL pixels (no data areas) in input raster map and stores filled data to a new output raster map. The fill areas are interpolated from the no data area boundaries buffer using v.surf.rst regularized spline interpolation with tension (method=rst) or r.resamp.bspline cubic or linear spline interpolation with Tykhonov regularization.

NOTES

Each area boundary buffer is set to three times the map resolution to get nominally three points around the edge. This way the algorithm interpolates into the hole with a trained slope and curvature at the edges, in order to avoid that such a flat plane is generated in a hole. The width of edge area can be adjusted by changing the edge parameter.

During the interpolation following warning may occur when using the RST method:

Warning: strip exists with insufficient data
Warning: taking too long to find points for interpolation--please change the region to area where your points are

This warning is generated if large data holes exist within the surface. As the idea of r.fillnulls is to fill such holes, the user may ignore the warning. The interpolation will be continued. However, the user may pay attention to below notes.

If interpolation fails, temporary raster and vector maps are left in place to allow unfilled map hole (NULL area) identification and manual repair.

When using the default RST method, the algorithm is based on v.surf.rst regularized splines with tension interpolation module which interpolates the raster cell values for NULL data areas from the boundary values of the NULL data area. An eventual raster MASK is respected during the NULL data area(s) filling. The interpolated values are patched into the NULL data area(s) of the input map and saved into a new raster map. Otherwise, either the linear or cubic spline interpolation with Tykhonov regularization can be selected (based on r.resamp.bspline).

WARNING

Depending on the shape of the NULL data area(s) problems may occur due to an insufficient number of input cell values for the interpolation process. Most problems will occur if a NULL data area reaches a large amount of the map boundary. The user will have to carefully check the result using r.mapcalc (generating a difference map to the input map and applying the "differences" color table with r.colors) and/or to query individual cell values.

RST method stores temporary maps on hard disk. It will require at least as much free space as one extra input raster map takes.

EXAMPLE

In this example, the SRTM elevation map in the North Carolina sample dataset location is filtered for outlier elevation values; missing pixels are then re-interpolated to obtain a complete elevation map:
g.region raster=elev_srtm_30m -p
d.mon wx0
d.histogram elev_srtm_30m
# remove too low elevations (esp. lakes)
r.mapcalc "elev_srtm_30m_filt = if(elev_srtm_30m < 50.0, null(), elev_srtm_30m)"
d.histogram elev_srtm_30m_filt
d.rast elev_srtm_30m_filt
r.fillnulls input=elev_srtm_30m_filt output=elev_srtm_30m_complete tension=20
d.histogram elev_srtm_30m_complete
d.rast elev_srtm_30m_complete

REFERENCES

SEE ALSO

r.fill.dir, r.mapcalc, r.resamp.bspline, v.surf.rst

AUTHORS

Markus Neteler, University of Hannover and Fondazione Edmund Mach
Improvement by Hamish Bowman, NZ

Last changed: $Date: 2015-12-31 00:19:29 -0800 (Thu, 31 Dec 2015) $

SOURCE CODE

Available at: r.fillnulls source code (history)


Note: A new GRASS GIS stable version has been released: GRASS GIS 7.6, available here.
Updated manual page: here

Main index | Raster index | Topics index | Keywords index | Graphical index | Full index

© 2003-2019 GRASS Development Team, GRASS GIS 7.2.4svn Reference Manual