r.catchment - GRASS GIS manual

Note: This document is for an older version of GRASS GIS that has been discontinued. You should upgrade, and read the current manual page.

NAME

r.catchment - Creates a raster buffer of specified area around vector points using cost distances using r.walk.

KEYWORDS

raster, buffer

SYNOPSIS

r.catchment

r.catchment --help

r.catchment [-ikcl] elevation=name [in_cost=name] start_points=name [friction=name] [walk_coeff=float] [lambda=float] [slope_factor=float] buffer=name [sigma=float] area=integer map_val=integer [name_column=name] [--overwrite] [--help] [--verbose] [--quiet] [--ui]

Flags:

-i: Iterate through each point in the input starting points vector map to create a series of catchment maps centered at each input point rather than a single map starting at all points. Maps will be named "'buffer'_'name'_'id#'", where 'buffer' is the value entered for option 'buffer', 'name' is the value in "name_column" for each input point and 'id#' is unique running id number. If no value specified in "name_column", cat value will be used in place of 'name'). NOTE: this function is NOT compatible with option "in_cost" or flag "l"
-k: Use knight's move for calculating cost surface (slower but more accurate)
-c: Keep cost surface(s) used to calculate buffers (follows similar naming convention from flag -i if -i is also selected)
-l: Show a list of all cost surface values and the area of the catchment that they delimit
--overwrite: Allow output files to overwrite existing files
--help: Print usage summary
--verbose: Verbose module output
--quiet: Quiet module output
--ui: Force launching GUI dialog

Parameters:

elevation=name [required]: Input elevation map (DEM)
in_cost=name: Input cost map (This will override the input elevation map, if none specified, one will be created from input elevation map with r.walk)
start_points=name [required]: Name of input vector map; Name of input vector site points map
friction=name: Optional map of friction costs. If no map selected, default friction=0 making output reflect time costs only; Default:
walk_coeff=float: Coefficients for walking energy formula parameters a,b,c,d; Default: 0.72,6.0,1.9998,-1.9998
lambda=float: Lambda value for cost distance calculation (for combining friction costs with walking costs); Default: 1
slope_factor=float: Slope factor determines travel energy cost per height step; Default: -0.2125
buffer=name [required]: Output buffer map name, or name-stem for all buffer maps created with flag -i
sigma=float: Slope threshold for mask
area=integer [required]: Area of buffer (Integer value to nearest 100 square map units); Default: 5000000
map_val=integer [required]: Integer value for output catchment area (all other areas will be Null); Default: 1
name_column=name: Database column for point names (with flag -i)

DESCRIPTION
- Options and flags:
NOTES
EXAMPLES
SEE ALSO
AUTHOR

DESCRIPTION

r.catchment is a module that facilitates modeling "catchments" around point locations according to a walking cost function. The module is particularly aimed at "Site Catchment Analysis" for archaeology, but could be potentially useful in any number of applications where delimiting an area based on walking-costs is desirable. Although defining a catchment based on a threshold in walking-costs (or time) can be undertaken using r.walk or r.cost alone, this addon module allows the user to enter a pre-determined square meterage (option area) for the resultant catchment, which is a different approach. This is useful for applications where the user wants to make a catchment of a particular size (e.g., certain number of square meters needed for farmed fields), and doesn't want to spend time via trial and error experimenting with different cost radii.

Additionally, this module allows the user to enter a slope threshold (option sigma), which will mask out areas of higher slope. This is useful for delimiting catchments that are of generally flat land (e.g., areas where agriculture are likely).

Optionally, you can iteratively loop through a series of input starting points, and create catchments for each point. You can also opt to save the cost map produced by r.walk for each input point. This can be a useful timesaver for the creation of many cost maps and/or catchment maps with minimal manual repetition.

Important: The user must run g.region first to make sure that the region boundaries and the resolution match the input elevation map.

Options and flags:

r.catchment requires an input elevation map, elevation , and an input vector points map of starting locations, start_points. area is also requited, which is an integer value for the size of the desired catchment (in the map units of the defined location/region). The final required parameter is map_val , which is the integer value to write to the areas defined as part of the catchment in the output map, buffer. The optional value, sigma is the slope threshold cut off value. Slopes above sigma will be masked out during the determination of the catchment configuration. The optional value name_column is to be used in conjunction with the -i flag (see below). There are three native flags for r.catchment. -c allows you to keep the interim cost surface maps made. -l allows you to show a list of the costv alues in that cost map, along with the size of the catchments they delineate. -i enable "iterative" mode. Here, the module will loop through all the points in the input vector file start_points, calculating a cost map and catchment map around each point. If name_column is specified, then each output map will contain the text value in that column as an prefix. Otherwise, the cat number for each vector point will be used. All other flags and options are inherited from r.walk (see the r.walk help page for more information on these).

NOTES

The module will attempt to find the cost radius that defines an area close to the value of area, but em will likely slightly overestimate the catchment size. The module will display the actual area of the defined catchment in the Command Output. By default, r.catchment will create a friction map of value 0, which, when input into r.walk will yield a cost surface based on walking times only. The user may optionally create a friction map, however, and, if used, r.walk will consider these costs this as well when determining the cost surface used to determine the catchment. The input start_points map should be a vector points map. If the file contains other types of features (areas, lines, centroids), these will be ignored. If you desire, a start points map could be manually digitized (with v.digit) over topographic or cultural features, or could be created as a series of random points (with r.random or v.random). Unless the -i flag is used, in the case of multiple input points, the routine will attempt to equally divide the area (area) between all input points tod etermine catchments for each point. The total area of all these catchments will sum (close) to area. If two input points are close, their catchments may overlap. In this case, the routine will "meld" the two, and the melded catchment will till be of an area close to area. If truly overlapping catchments are desired, then the routine should be run with the -i flag. This will create completely independent catchments around each input point.

EXAMPLES

Delimit a catchment of 5,000,000 square meters around a single start point, ignoring areas of slope > 15 degrees:

r.catchment elevation=DEM10m start_points=site buffer=test_catchment
sigma=15 area=5000000 map_val=1

AUTHOR

Isaac Ullah

Updated for GRASS 8, 02, Feb. 2023.

SOURCE CODE

Available at: r.catchment source code (history)

Latest change: Monday Jun 24 08:16:48 2024 in commit: 8939a985d18de5366340b88037ab0fe3a0814c9b